The all-black Sony TA-F555ES is 17 inches wide, 13-3/4 inches deep, and 5-1/8 inches high, and it weighs about 30 pounds. Laboratory Measurements Our test sample of the Sony TA-F555ES (an early production unit) was supplied without an instruction manual or schematic. Sony TA-E80ES - Manual - Stereo Control Amplifier - HiFi. Sony Ta F555esx Manual. Download Sony ta. Vintage audio gear!
Download Installation manual of Directed Xpresskit DBALL2 Automobile Accessories, Remote Starter for Free or View it Online on All-Guides.com.
Brand: Directed
Category: Automobile Accessories , Remote Starter
Type: Installation manual for Directed Xpresskit DBALL2
Pages: 12
To enter feature programming routine
Turn the ignition ON, then OFF.
Within 5 seconds, press and HOLD the programming button until the LED turns ON orange (after 3 seconds). Release the
-
The LED will flash green once slowly to indicate the feature number is 1. After a short delay, the LED flashes red rapidly to indicate
the current option of feature 1 (i.e. 1x green followed by 1x red indicates feature 1 is set to option 1). The flashing sequence will repeat
Changing feature options
Press the lock/arm or unlock/disarm button on aftermarket transmitter to change the option of the selected feature.
The LED flashes red rapidly the number of times equal to the current option number. After a short delay, the LED flashes green slowly
the number of times to indicate the current feature. The flashing sequence will repeat until a new command is entered.
-
Press and release the programming button a number of times to advance from the current feature to the next desired feature.
The LED flashes green slowly the number of times equal to the feature number. After a short delay, the LED flashes red rapidly to
indicate the current option of the current feature. The flashing sequence will repeat until a new command is entered.
When the maximum number of features or options is reached, the LED will start flashing again from the first feature or option.
-
-
Exiting feature programming
No activity for 30 seconds; after 30 seconds, the LED will turn ON orange for 2 seconds to confirm the end of the programming
OR
Press and HOLD the programming button for 3 seconds. After 3 seconds, the LED will turn ON orange for 2 seconds to confirm the
Feature Programming
Button
It is recommended to configure all the features and options listed below using the configuration tool found on the module
flashing page on www.directechs.com. The web offers more options; however, manual configuration of the features is
* Default Option
1. No RF Output*Module is connected to a remote starter using a standard installation.
2. RFTD OutputModule is connected to an XL202 using an RSR or RXT installation (when available).
3. SmartStartModule is connected to SmartStart using anRSR or RXT installation (when available).
2. With IgnitionLocks alldoors when ignition is ON. Unlocks driver door whenignition turns OFF.
Locks alldoors when brake pedal is pressed while vehicle is running. Unlocks driver door
4. With SpeedLocks alldoors when the vehicle is moving. Unlocks driver door when ignition is turned OFF.
TheOEM alarmwill not be controlled byDBALL upon remote start. No disarmor arm
command will be executed at the beginning or endof thesequence; it must be controlled by
2. Safelock
Smart OEM Alarm Control will behave like a standardSafelock feature on a remote starter. It
will unlock at thebeginningof the sequence, and relock after start and shutdown.
Smart OEM Alarm Control will synchronize with theOEM alarmso that it will disarmand rearm
the vehicle intheremote start sequence, only when required. Thereason for this is, factory
alarm control must often be done by lock or unlock operation. This could create unnecessary
![Sony ta f555esx manual transmission manual Sony ta f555esx manual transmission manual](/uploads/1/2/6/2/126227991/581397421.jpg)
actions ondoor lock modules, such as thehorn to honk. When possible, Smart OEMAlarm
Control will monitor thealarm and door lock status to detect if the disarmor rearm is required.
If the vehicleis unlocked or is not equipped with factory alarm, thedisarm/rearm will not be
executed. Smart OEM Alarm Control will also monitor theremote starter actions so that the
factory alarm control is not done twice. A remote starter, for which theSafelock feature is active,
will work perfectly with thisoption and will make it invisible to theuser.
Smart OEM
![Transmission Transmission](/uploads/1/2/6/2/126227991/830003719.jpg)
1
Type
Automatic
Lock
Platform: DBALL2
© 2017 Directed. All rights reserved.
12
C-410
C-418
Fuse Box
MS CAN High: White, pin 10
Gray 22-pin conn.
1615141312
212220191817